The One Stop Shop for all of your
Machinery, Equipment, Tool & Die Needs
Gold International Machinery | The One Stop Shop for all of your Machinery, Equipment, Tool & Die Needs

8536-460 Brown & Sharpe Universal Sliding Head Horizontal/Vertical Milling Machine,Rangemaster #20

Scroll Down To See Video!

Inventory Number: 8536-460

Technical Specifications:

  • 220V/3PH/50-60HZ
  • S/N: 506-20-32
  • Table working surface: 10" x 50"
  • Table Swivels: plus or minus 50 degrees
  • Number and width of table t-slots: (3) 11/16"
  • Table travel: 29" x 11"
  • Knee travel: 14"
  • Top ram travel: 24"
  • Spindle taper, horizontal: #50 N.S.T.
  • Spindle taper, universal milling head: #40 N.S.T.
  • Axial feed (hand feed) of universal milling head: 3-1/2"
  • Transverse adjustment of sliding head: 22-7/8"
  • (18) Feeds: 1/2 to 20-1/4 I.P.M.
  • (18) Speeds, horizontal: 40 to 1,530 R.P.M.
  • (18) Speeds, universal milling head: 80 to 3,060 R.P.M.
  • Rapid traverse rate, all directions: 75 I.P.M.
  • Minimum/Maximum distance from centerline of  horizontal spindle to top of table: 21/32" / 21-5/8"
  • Distance from centerline of universal milling head spindle to column face: 2-1/16 / 24-15/16"
  • Spindle speeds: 40 - 1535 RPM
  • Number of speeds: 18
  • Table feeds: 1-1/2 - 20-1/4 IPM (19)
  • Overall dimensions: 64" x 76" x 80" H
  • Approximate Weight: 5,350 Lbs

Equipped With:

  • Universal, swivel table
  • Universal (double swivel) milling head with manual micrometer quill travel
    • Sliding head design allowing the spindle and its driving motor to be extended so that its face is up to 15-3/16" away from the machine column face. This permits the spindle nose to be brought out close to the cutter while adequate clearance is given to work or fixtures projecting over the table. Another advantage of the sliding head design is obtained when an end mill is being used in the nose of the horizontal spindle.
  • (1) Arbor support
  • Approximately (10) #50 N.S.T. tool holders
  • Approximately (18) #40 N.S.T. tool holders
  • Manual draw bolt for both horizontal and vertical spindles
  • Movable pendant control
  • Self-contained coolant pump
  • 1 H.P. feed motor
  • 3 H.P. 3/60/220-440 volt spindle drive motor and electrical controls
  • Manual included


Click On Images To View Full Size:
Video:



You may also call us at: 1-800-619-GOLD
between the hours of 9am and 5pm EST
OR E-Mail David Gold at DGOLD@GoldMachinery.com

Financing Available - Low Monthly Payments

© Gold International Machinery 2015

[ Mailing Address | Gold International Machinery, Corp | P.O. Box 998 Pawtucket, RI 02862 ]
[ Physical Address: | 136 Newell Avenue | (corner of Thurston & Newell Sts.) | @Exit 26, Route 95 North | Pawtucket, RI USA 02860-0998 ]
[ mail@goldmachinery.com | Toll Free: 1-800-619-GOLD | Phone: 401-724-3200 | Fax: 401-728-5770 ]